There is an increased risk of electric shock if your body is earthed or grounded. Water entering a power tool will increase the risk of electric shock. Never use the cord for carrying, pulling or unplugging the power tool. Keep cord away from heat, oil, sharp edges or moving parts.
VAC photos on Flickr | Flickr
Damaged or entangled cords increase the risk of electric shock. Use of a cord suitable for outdoor use reduces the risk of electric shock 3 Personal safety a Stay alert, watch what you are doing and use common sense when operating a power tool. Do not use a power tool while you are tired or under the influence of drugs, alcohol or medication.
A moment of inattention while operating power tools may result in serious personal injury. Always wear eye protection. Safety equipment such as dust mask, non-skid safety shoes, hard hat, or hearing protection used for appropriate conditions will reduce personal injuries. Ensure the switch is in the off position before plugging in. Carrying power tools with your fi nger on the switch or plugging in power tools that have the switch on invites accidents.
A wrench or a key left attached to a rotating part of the power tool may result in personal injury. Keep proper footing and balance at all times. This enables better control of the power tool in unexpected situations. Do not wear loose clothing or jewellery. Keep your hair, clothing and gloves away from moving parts. Loose clothes, jewellery or long hair can be caught in moving parts. Use of these devices can reduce dust related hazards. Use the correct power tool for your application.
The correct power tool will do the job better and safer at the rate for which it was designed. Any power tool that cannot be controlled with the switch is dangerous and must be repaired. Such preventive safety measures reduce the risk of starting the power tool accidentally. Power tools are dangerous in the hands of untrained users. Check for misalignment or binding of moving parts, breakage of parts and any other condition that may affect the power tools operation.
If damaged, have the power tool repaired before use. Many accidents are caused by poorly maintained power tools. Properly maintained cutting tools with sharp cutting edges are less likely to bind and are easier to control. Use of the power tool for operations different from intended could result in a hazardous situation. This will ensure that the safety of the power tool is maintained.
Popular Instagram Photos
When not in use, tools should be stored out of reach of children and infirm persons. Wear the dust mask additionally, if available. When ordering, specify the grain type and grain size desired. Stationary Stand When sanding small articles, use a stationary stand for convenience. Optional accessories are subject to change without notice. Base polishing of wood-coated surfaces. Finish sanding of metal surfaces.
Base polishing of metal-coated surfaces, rust removal, or paint removal prior to refinishing. Surface finishing of slate, concrete, and similar materials. Power source Ensure that the power source to be utilized conforms to the power requirements specified on the product nameplate. Power switch Ensure that the power switch is in the OFF position. If the plug is connected to a receptacle while the power switch is in the ON position, the power tool will start operating immediately, which could cause a serious accident.
Extension cord When the work area is removed from the power source, use an extension cord of sufficient thickness an rated capacity. The extension cord should be kept as short as practicable. Attach the sanding belt For details, refer to the section on Sanding Belt Assembly. How to attach sanding belt 1 Pull lever with finger, idle pulley will then move backward.
English 2 Place on drive pulley and idle pulley passing it over the outside of shoe plate and making sure that arrow on inside of belt coincides with rotational direction of drive pulley. In this case, be careful not to be hit yourfi nger by lever. Then, adjust sanding belt position. How to remove sanding belt Pull lever withfi nger, sanding belt will then sag and can be taken off pulleys eqsily.
Remove dust from the bag as follows: 1 Loosen the support bar and remove the dust bag. How to adjust sanding position. Push switch and turn sanding belt to check position. Adjust sanding belt so that both edges protrude 1. Adjust sanding belt position by turning adjust screw. Turn adjust screw counterclockwise to move belt out. To turn on switch Turn on switch while holding machine away from surface to be worked on.
If machine is placed on surface when switch is pushed, surface may be badly scratched. The same applies when stopping the machine.
Dantri.com.vn
How to hold machine Grasp handle and handle knob and hold machine against surface to be worked on so that it contacts surface lightly. Weight of machine itself is sufficient for sanding and polishing at highest efficiency. Do not apply any additional pressure, for this would place unnecessary load on motor, shorten life of sanding belt and lower work efficiency.
How to move machine Move mechine forwardfi rst and then backward, repeating this motion. How to select proper sanding belt Choose sanding belt of proper grain size and grain type for your specific purpose, by referring to Table 2 and 3 below. Use sanding belt of same grain size until uniform surface is obtained. Changing grain sizes may result in poor fi nish. How to operate switch The power switch is turned ON when the trigger is pulled, and if the stopper is once depressed, the power switch becomes locked, allowing continuous operation.
The stopper can be released pulling the trigger. Adjusting the belt speed: SB10V2 The Belt Sander is equipped with the electric control circuit which enables stepless speed control. To adjust the speed, turn the dial shown in Fig. When the dial is set to 1, the belt sander operates at the minimum speed. When the dial is set to 5, the belt sander operetes at the maximum speed.
How to work on corner Corners can be sanded and polished by using machine as in Fig.
- gay torrevieja spain.
- SB 10V2 SB 10S2 Handling Instructions Instrucciones de manejo.
- consulta tarot por email gratis.
- orgullo gay murcia 2020 programacion.
Inspecting the sanding belt Since continued use of a worn-out sanding belt will degrade efficiency, replace the sanding belt as soon as excessive abrasion is noted. Inspecting the mounting screws Regularly inspect all mounting screws and ensure that they are properly tightened. Should any of the screws be loose, retighten them immediately.
Failure to do so could result in serious hazard. Maintenance of the motor The motor unit winding is the very heart of the power tool. Inspecting the carbon brushes For your continued safety and electrical shock protection, carbon brush inspection and replacement on this tool should ONLY be performed by a Hitachi Authorized Service Center.
Replacing supply cord If the supply cord of Tool is damaged, the Tool must be returned to Hitachi Authorized Service Center for the cord to be replaced. English 6.
- free gay phone chat atlanta georgia?
- Home - domain expired?
- gay guide cartagena colombia.
Service parts list A: Item No. B: Code No. C: No. This Parts List will be helpful if presented with the tool to the Hitachi Authorized Service Center when requesting repair or other maintenance. In the operation and maintenance of power tools, the safety regulations and standards prescribed in each country must be observed. Accordingly, some parts i. El término herramienta eléctrica en todas las advertencias indicadas a continuación hace referencia a la herramienta eléctrica que funciona con la red de suministro con cable o a la herramienta eléctrica que funciona con pilas sin cable.
Las zonas desordenadas y oscuras pueden provocar accidentes. Las herramientas eléctricas crean chispas que pueden hacer que el polvo desprenda humo. Las distracciones pueden hacer que pierda el control. No modifique el enchufe. No utilice enchufes adaptadores con herramientas eléctricas conectadas a tierra. No utilice el cable para transportar, tirar de la herramienta eléctrica o desenchufarla. Mantenga el cable alejado del calor, del aceite, de bordes afilados o piezas móviles.
Los cables dañados o enredados aumentan el riesgo de descarga eléctrica. La utilización de un cable adecuado para usarse al aire libre reduce el riesgo de descarga eléctrica. All rights reserved. Y dije a tus discípulos que lo expulsaran, pero no pudieron.